![]() The move to Automotive Ethernet provides higher-quality, lower latency, time synchronization of audio and video in Ethernet standard format to transmit realtime audio and video streams. But these standards are now outdated in terms of payload, speed, etc. Trap monitoring of specific events can be selectively enabled or disabled by the network management software.Controller area network (CAN) and other existing technologies like LIN, Flexray, MOST were used as system buses in the automotive field earlier days. The iConverter T1/E1 supports SNMP trap notification for the monitoring and notification of different network events. Specific events that generate traps include module insertion and removal, and port link-up and link-down. #T1 media converter serial numbersThe management software can override the physical DIP-switch settings such as line settings and loopback control. Some of the real-time T1/E1 parameters that can be monitored include power, link, data status, module type and model, hardware and software revisions, serial numbers and a user-defined identifier. The T1/E1 can be managed with Omnitron’s intuitive, graphic-oriented NetOutlook SNMP Management Software or third party SNMP management software. Management via the Telnet and the serial interfaces have an easy-to-use, menu-driven interface. The Management Module can be accessed via SNMP, Telnet, and serial port. Management of the T1/E1 plug-in module is accomplished by installing an iConverter Management Module (NMM2) or Network Interface Device (NID) in the same chassis. Management provides remote configuration, monitoring and trap notification. The iConverter T1/E1 plug-in module can be used in managed or unmanaged applications. The T1/E1 standalone unit is available as a wall-mount unit. The wall-mount models are DC powered and are available with an external AC to DC power adapter or a terminal connector for DC power. It can also be mounted in a 2-Module AC or 18 to 60VDC powered chassis, or in a 1-Module AC or DC powered chassis. The hot-swappable plug-in module can be mounted in a 19-Module (2U high) or 5-Module (1U high) rack-mountable chassis (19-inch or 23-inch) with redundant AC, 24VDC or 48VDC power supplies. The copper interface features an RJ-48 connector for balanced T1/E1 applications, and models featuring coaxial BNC connectors are available for unbalanced E1 applications. The iConverter T1/E1 features user-selectable Local Loopback, Force 1s to Copper, Force 1s to Fiber, and Fiber Optic Test modes to facilitate diagnosis of the remote unit, eliminating the cost of external hardware or support personnel at each end of a link. DIP-switches provide easy configuration of T1/E1 line codes and line build-out. The converter also supports AMI, B8ZS and HDB3 line codes. The T1/E1 also supports multimode and single-mode dual fiber with ST, SC and LC connectors and single-mode single-fiber with SC connectors.ĭesigned as a transparent repeater, the iConverter T1/E1 supports standard T1, E1 and Primary Rate Interface (PRI), voice or data. The T1/E1 supports both standard and CWDM Small Form Pluggable (SFP) transceivers, enabling adaptability to different fiber types, distances and wavelengths, providing maximum flexibility across a variety of network architectures and topologies. The iConverter T1/E1 media converters operate in pairs, extending distances over fiber, which improves noise immunity, quality of service, intrusion protection and network security. The iConverter T1/E1 can be used to extend the demarcation point between service provider and networking equipment. The iConverter T1/E1 is a T1 (1.544Mbps) or E1 (2.048Mbps) copper to fiber media converter, and is available as a compact unmanaged standalone unit or a managed chassis plug-in module. #T1 media converter freeLifetime Warranty and free 24/7 Technical Support.Commercial (0 to 50☌) and wide (-40 to 60☌) temperature ranges.SNMP management via NetOutlook® provides real-time port and module status information, remote parameter configuration and trap notification.Management is available with the addition of a management module to the chassis.Plug-in modules are hot-swappable in 19-Module, 5-Module, 2-Module or 1-Module chassis.LED displays for immediate visual status of each port.Supports SFP Digital Diagnostic Monitoring Interface (DDMI) bus.Small Form Pluggable (SFP) transceivers with standard and CWDM wavelengths.Supports multimode and single-mode dual fiber with ST, SC and LC connectors and single-mode single-fiber with SC connectors.User-selectable Local Loopback, Force 1s on Copper or Fiber and Fiber Test modes.Easy configuration of T1/E1 line codes and line buildout.Supports T1, E1 and Primary Rate Interface voice and data.The T1/E1 is a RJ-48 or coaxial to fiber media converter that supports ANSI, AT&T, ETSI and ITU standards ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |